The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

Low-Side Cascading Kit (Two Stage, 376mm Travel)

SKU:

The Two Stage Low-Side Cascading Kit utilizes 1121 Series Low-Side U-Channel as the framework of this very smooth and stable cascading kit. Ball bearings in each stage minimize friction while acetal side plates assist in guiding the stages as they extend and retract. The v-groove pulleys, synthetic cable and dual-spool pulley included in the kit provide a reliable drive that is powered both in the extension and retraction.

Use the kit in any orientation, whether you’re reaching up or out. The maximum travel (difference between retracted and extended) is 376mm (just shy of 15”) while measuring only 306mm (12”) tip to toe in the retracted state. The mechanical stops can be adjusted every 8mm on each stage if you wish to tailor the travel to your specific application. If you choose to do-so, limiting the lower stage will yield slightly faster transit times given the upper stage has less mass moving with it.

The kit comes with all the necessary pieces, minus the motor, to get you up and going. The included 32mm clamping mounts are compatible with the goBILDA 5202 Series Yellow Jacket Gear Motors. Tailor your travel speed with the various ratios we offer. The included pulley has a diameter of 38mm (1.5”) which yields 120mm (4.75”) of travel per rotation. Given the max travel of 376mm, it takes approximately 3.1 rotations of the motor shaft to reach full extension. A 13.7:1 ratio (435 RPM) gear motor is the fastest that we recommend, as it’s able to fully extend the two stages in about ½ second! With such a fast potential transit speed it’s recommended to utilize the encoder on the 5202 Series motor so you can start and stop your cascading kit at the limits of the travel.

 

Kit Contents:

SKUQtyName
1121-0009-0240 2 1121 Series Low-Side U-Channel (9 Hole, 240mm Length)
1121-0011-0288 1 1121 Series Low-Side U-Channel (11 Hole, 288mm Length)
1309-0016-1006 1 1309 Series Sonic Hub (6mm D-Bore)
1400-0032-0032 2 1400 Series 1-Side, 2-Post Clamping Mount (32mm Bore)
1502-0006-0050 1 1502 Series 4mm ID Spacer (6mm OD, 5mm Length) - 4 Pack
1600-0410-0004 8 1600 Series Non-Flanged Ball Bearing (4mm ID x 10mm OD, 4mm Thickness) - 2 Pack
1609-0613-0004 2 1609 Series V-Groove Bearing (4mm ID x 13mm OD, 6mm Thickness) - 2 Pack
2800-0004-0010 1 2800 Series Zinc-Plated Steel Socket Head Screw (M4 x 0.7mm, 10mm Length) - 25 Pack
2801-0004-0008 1 2801 Series Zinc-Plated Steel Washer (4mm ID x 8mm OD) - 25 Pack
2802-0004-0012 1 2802 Series Zinc-Plated Steel Button Head Screw (M4 x 0.7mm, 12mm Length) - 25 Pack
2802-0004-0014 1 2802 Series Zinc-Plated Steel Button Head Screw (M4 x 0.7mm, 14mm Length) - 25 Pack
2802-0004-0016 1 2802 Series Zinc-Plated Steel Button Head Screw (M4 x 0.7mm, 16mm Length) - 25 Pack
2802-0004-0022 1 2802 Series Zinc-Plated Steel Button Head Screw (M4 x 0.7mm, 22mm Length) - 25 Pack
2802-0004-0025 1 2802 Series Zinc-Plated Steel Button Head Screw (M4 x 0.7mm, 25mm Length) - 25 Pack
2807-0407-0250 2 2807 Series Stainless Steel Shim (4mm ID x 7mm OD, 0.25mm Thickness) - 12 Pack
2812-0004-0007 2 2812 Series Zinc-Plated Steel Nylon-Insert Locknut (M4 x 0.7mm, 7mm Hex) - 25 Pack
2908-0075-0005 1 Synthetic Cable (Black, 0.75mm Diameter, 5M Length)
2914-0002-0001 2 V-Groove Bearing Shield (2-1) - 2 Pack
2915-0001-0001 1 Extension Spring (8mm OD, 6.8kg Max Load, 80-120mm Length)
3407-0016-0001 1 3407 Series Hub Mount Winch Pulley (16-1)
3705-0001-0004 1 Side Plate for Low-Side Cascading Kit - 2 Pack
3705-0001-0005 1 Stop Plate for Low-Side Cascading Kit - 2 Pack
3705-0001-0006 1 Spring Mounting Plate for Low-Side Cascading Kit
4200-0090-0025 1 2.5mm Hex L-Key
4200-0090-0030 1 3mm Hex L-Key
4202-0070-1070 1 7mm Combination Wrench

Specs

Weight 516g (1.14lbs)
$99.99